Q.1.

The approximate height of a blast furnace having a useful volume ofm3 is about __________ metres

Q.2.

Air standard Otto cycle is more efficient than the diesel cycle for the same

Q.3.

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.

Q.4.

Stellite is a __________ material.

Q.5.

Most of the phosphorous present in the blast furnace burden enters into

Q.6.

During sensible heating of humid air

Q.7.

The most important requirement for aluminium industry is the availability of cheap

Q.8.

Spheriodising of a material is a/an __________ process.

Q.9.

Most important property of steels for use in automobile bodies is the

Q.10.

Consideration of the creep is the most important in case of the

Q.11.

The driving force for the sintering of a powder compact is

Q.12.

When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively

Q.13.

Preheating before welding is done to

Q.14.

Catalyst used in the catalytic converter employed in automobiles to convert CO into CO and for complete oxidation of un-burnt hydrocarbons is

Q.15.

Spark plug is provided in a/an

Q.16.

Which of the following gases cause global warming ?

Q.17.

Rankine cycle comprises of two isothermal and two __________ processes.

Q.18.

Desalination of water

Q.19.

Viscoelastic behaviour is observed in __________ materials.

Q.20.

Temperature attained in soldering of metals is about __________ °C.

Q.21.

Pick out the correct statement.

Q.22.

Thermal conductivity of a material does not depend upon its

Q.23.

Multistage compression is necessary for high efficiency,

Q.24.

A freely floating object is stable, if its centre of buoyancy

Q.25.

Which of the following heat treatment processes is usually applied to castings ?

Q.26.

Nusselt number/Biot number varies

Q.27.

Cold working of a material results in increase in hardness, which is termed as the __________ hardening.

Q.28.

The cathode in an electrochemical cell always carries

Q.29.

A suitable lubricant used for watches is

Q.30.

Percentage of argon (by volume) in dry atmospheric air is about

Q.31.

The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.

Q.32.

Limestone addition in the blast furnace is done to flux __________ present in the raw materials.

Q.33.

Thermal diffusivity of a substance is proportional to (where, k = Thermal conductivity)

Q.34.

Dew point temperature always gives an indication of the __________ of the moist air.

Q.35.

For a thermodynamic system undergoing a process, which of the following pairs best expresses the relationship similar to that expressed by the pressure volume plot ?

Q.36.

Oxyacetylene reducing flame is used while carrying out welding on

Q.37.

Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as

Q.38.

Multistage compression of air as compared to single stage compression offers the advantage of

Q.39.

Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation

Q.40.

The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam.

Q.41.

If a solid is compressed adiabatically in its elastic range, its __________ remains constat

Q.42.

The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.

Q.43.

Notched bar test is used for testing the __________ of a material.

Q.44.

Glass reacts with

Q.45.

__________ can not increase the fatigue strength of a material.

Q.46.

If the head is doubled in & centrifugal pump, the power required will increase in the ratio of

Q.47.

Which of the following materials does not form adherent oxide film on surface ?

Q.48.

Out of the following, maximum temperature drop for a given heat flow & for the same thickness will be in the case of

Q.49.

Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type

Q.50.

An oxidation process is accompanied with decrease in the