If you are asked to complete an offset back/left parking maneuver, you should first pull straight forward, then back up to the left. Your vehicle must be parked completely within the boundaries of the parking space.

If it is necessary to evacuate a school bus, students should be led by the driver in the direction of oncoming traffic to a safe location that is at least 100 feet off the road. This will help to ensure that they are not hit by flying debris if another vehicle hits the bus.

In general, school bus drivers should stop before any railroad crossings to check the tracks for approaching trains. Drivers should stop no closer than 15 feet, and no farther than 50 feet, from the nearest rail in order to have the best view of the tracks. They should look and listen for approaching trains before proceeding through the crossing.

When exiting your vehicle during the basic vehicle control skills test, you must face the vehicle and maintain three points of contact at all times. If your testing vehicle is a bus, you must maintain contact with the handrail. Exiting the vehicle incorrectly may result in automatic failure of the basic control skills test.

In most emergency situations, students will be safest and best kept under control if they do not evacuate the school bus.

Properly adjusted flat mirrors on a school bus should allow the driver to see 200 feet behind the bus, the base of each rear wheel, and the sides of the bus.

Before a trip, ensure that the steering box is securely mounted. Check for missing nuts, bolts, and cotter keys. Be sure that there are no power steering fluid leaks and that there is no damage to power steering hoses.

A school bus driver should never change or add a stop without written approval from the appropriate school district officials.

While taking the on-road driving skills test, check for traffic and use your mirrors regularly, especially when encountering intersections. Scan and check for pedestrians in areas where they may be present.

When exiting your vehicle during the basic vehicle control skills test, you must face the vehicle and maintain three points of contact at all times. If your testing vehicle is a bus, you must maintain contact with the handrail. Exiting the vehicle incorrectly may result in automatic failure of the basic control skills test.

Outside convex mirrors on a school bus are located below the outside flat mirrors. They are used to see a wide view of traffic, clearance, and students around the bus.

When inspecting a trailer during a vehicle inspection test, ensure that its landing gear has no missing parts and that it is fully raised. The crank handle should be secure and the support frame should not be damaged.

If a school bus needs to be evacuated in the event of an emergency, the driver must quickly determine which exit or exits will be safest for students to use and direct the students to that exit.

If approaching a railroad crossing while driving a transit bus, school bus, or placarded vehicle, special procedures apply. Before crossing, stop your vehicle within 50 feet of, but not less than 15 feet from, the nearest rail. Activate your four-way flashers while crossing. Do not stop, change gears, or change lanes while any part of your vehicle is proceeding across the tracks.

An Anti-Lock Braking System (ABS) is in place as an addition to a braking system. It intervenes to prevent brakes from locking up during hard braking. If ABS is not working, the basic braking functions on a vehicle will still remain, so the driver can continue to drive and brake normally.

More students are killed each year during loading or unloading of school buses than while riding on school buses. Therefore, it is critical that school bus drivers follow appropriate safety procedures during loading and unloading. The process must be properly supervised and done with care.

During the on-road driving skills test, you may be asked to drive on an expressway. Make sure you maintain proper lane positioning, vehicle spacing, and vehicle speed. Continue to thoroughly check traffic in all directions while on the expressway.

Passive railroad crossings are not controlled by any traffic control devices. At such crossings, it is entirely a driver's responsibility to determine when it is safe to cross the tracks.

During the on-road driving test, you must listen to and follow the directions given by the examiner. They will never ask you to drive in an unsafe manner.

Maneuvers that may be included in the basic vehicle control skills test include straight line backing, offset back/right parking, offset back/left parking, driver side parallel parking, conventional parallel parking, and alley docking.